1.配置AC1为VRRP组1的Master，配置HSB(双机热备份功能)，将AC1上的业务信息通过备份链路批量备份、实时备份到AC2上，保证在主设备故障时业务能够不中断地顺利切换到备份设备 1）在AC1上创建管理...

图10-4  QinQ基础配置网络拓扑 1.配置基础QinQ 1）SW1配置 [SW1]vlan 100 [SW1]interface GigabitEthernet 0/0/23 [SW1-GigabitEthernet0/0/23]port link-type dot1q-tunnel [SW1-GigabitEther...

图2-9 OSPF 路由汇总网络拓扑 1.ABR上对域间路由进行汇总 1）汇总前查看R3环回口路由 <R5>display ip routing-table 3.3.3.3 3.3.3.3/32 OSPF 10 2 D 45.1.1.4 GigabitEthernet0/0/1 2）在AB...

1.配置防火墙接口1/0/1 [FW1]interface GigabitEthernet 1/0/1 [FW1-GigabitEthernet1/0/1]ip address 192.168.1.254 24 [FW1-GigabitEthernet1/0/1]service-manage ping permit //接口允许ping...

图8-6 ISIS手动产生默认路由网络拓扑 1.查看R1、R6默认路由（由Level-1-2产生缺省路由） <R1>display ip routing-table protocol isis 0.0.0.0/0 ISIS-L1 15 10 D 12.1.1.2 GigabitEthernet0...

图2-8 OSPF LSA信息网络拓扑 1.R1配置RIPv2 [R1]rip 1 [R1-rip-1]version 2 [R1-rip-1]undo summary [R1-rip-1]network 1.0.0.0 [R1-rip-1]network 12.0.0.0 2.R2配置RIPv2 [R2]rip 1 [R2-rip-1...

图4-7  优选从EBGP邻居学习到的路由网络拓扑 1.R1配置OSPF [R1]ospf 1 router-id 1.1.1.1 [R1-ospf-1]area 0 [R1-ospf-1-area-0.0.0.0]network 1.1.1.1 0.0.0.0 [R1-ospf-1-area-0.0.0.0]netwo...

5.1 路由反射器 图5-1 BGP路由反射器网络拓扑 1.R2配置OSPF [R2]ospf 1 router-id 2.2.2.2 [R2-ospf-1]area 0 [R2-ospf-1-area-0.0.0.0]network 2.2.2.2 0.0.0.0 [R2-ospf-1-area-0.0.0.0]netwo...

图17-2 ISIS for IPV6基本配置网络拓扑 1.R1配置接口IP地址 [R1]ipv6 [R1]interface GigabitEthernet 0/0/0 [R1-GigabitEthernet0/0/0]ip address 12.1.1.1 8 [R1-GigabitEthernet0/0/0]ipv6 en...

图18-11 负载分担VRRP配置网络拓扑 1.R2配置VRRP [R2]interface GigabitEthernet 0/0/1 [R2-GigabitEthernet0/0/1]vrrp vrid 1 virtual-ip 23.1.1.254 [R2-GigabitEthernet0/0/1]vrrp vrid 1 pr...