图4-7  OSPF虚电路网络拓扑 1.R1配置 [R1]ospf 1 router-id 1.1.1.1 [R1-ospf-1]area 0 [R1-ospf-1-area-0.0.0.0]network 1.1.1.1 0.0.0.0 [R1-ospf-1-area-0.0.0.0]network 12.1.1.0 0.255.25...

图19-4 OSPFv3基本配置网络拓扑 1.R1配置OSPFv3 [R1]ospfv3 1 [R1-ospfv3-1]router-id 1.1.1.1 [R1]interface GigabitEthernet 0/0/0 [R1-GigabitEthernet0/0/0]ospfv3 1 area 0 [R1]interface ...

1.R4引入一条默认路由，R1查看OSPF路由信息 [R4]ospf 1 [R4-ospf-1]default-route-advertise always <R1>display ip routing-table protocol ospf Destination/Mask Proto Pre Cost Flags Ne...

1.R3查看OSPF路由信息 [R3]display ip routing-table protocol ospf Destination/Mask Proto Pre Cost Flags NextHop Interface 0.0.0.0/0 O_ASE 150 1 D 34.1.1.4 GigabitEthernet0/0/0 1.1.1....

1.查看SW1的实例1根为SW1 [sw1]display interface Hardware address is 4c1f-ccfb-35ef [sw1]display stp instance 1 -------[MSTI 1 Global Info]------- MSTI Bridge ID :4096.4c1f-ccfb-35ef...

图4-6  OSPF路由引入网络拓扑 1.R3新生成直连路由，宣告进OSPF [R3]interface LoopBack 0 [R3-LoopBack0]ip address 3.1.2.1 255.255.255.0 sub [R3-LoopBack0]ip address 3.1.3.1 255.255.255...

图6-1 交换机基本配置网络拓扑 1.初始状态交换机MAC地址表为空 [SW1]display mac-address 2.PC1去ping未知IP地址192.168.1.3，在PC2接口抓包 图6-2 SW3 G0/0/1口抓包 3.查看SW1交换机MAC地址表,...

图5-1 基本配置网络拓扑 1.AS 234内配置OSPF [R2]ospf 1 router-id 2.2.2.2 [R2-ospf-1]area 0 [R2-ospf-1-area-0.0.0.0]network 2.2.2.2 0.0.0.0 [R2-ospf-1-area-0.0.0.0]network 23.1.1.0 0....

图4-5  OSPF路由引入网络拓扑 1.R4创建新的直连路由，OSPF引入外部路由 [R4]interface LoopBack 1 [R4-LoopBack1]ip address 44.1.1.1 32 [R4-LoopBack1]quit [R4]interface LoopBack 2 [R4-Lo...

图17-1 DHLC、PPP配置网络拓扑 1.R1、R2配置 [R1]interface Serial 0/0/0 [R1-Serial0/0/0]link-protocol hdlc [R1-Serial0/0/0]ip address 12.1.1.1 30 [R2]interface Serial 0/0/0 [R2-Serial...