图9-1 VLAN间路由配置网络拓扑 1.SW1配置VLAN [SW1]vlan batch 10 30 [SW1]interface GigabitEthernet 0/0/1 [SW1-GigabitEthernet0/0/1]port link-type access [SW1-GigabitEthernet0/0/1]port...

图6-1 交换机基本配置网络拓扑 1.初始状态交换机MAC地址表为空 [SW1]display mac-address 2.PC1去ping未知IP地址192.168.1.3，在PC2接口抓包 图6-2 SW3 G0/0/1口抓包 3.查看SW1交换机MAC地址表,...

1.R3查看OSPF路由信息 [R3]display ip routing-table protocol ospf Destination/Mask Proto Pre Cost Flags NextHop Interface 0.0.0.0/0 O_ASE 150 1 D 34.1.1.4 GigabitEthernet0/0/0 1.1.1....

图5-1 基本配置网络拓扑 1.AS 234内配置OSPF [R2]ospf 1 router-id 2.2.2.2 [R2-ospf-1]area 0 [R2-ospf-1-area-0.0.0.0]network 2.2.2.2 0.0.0.0 [R2-ospf-1-area-0.0.0.0]network 23.1.1.0 0....

1.R1配置全局DHCP [R1]dhcp enable [R1]ip pool dsrw.com R1-ip-pool-dsrw.com]gateway-list 192.168.1.254 [R1-ip-pool-dsrw.com]network 192.168.1.0 mask 255.255.255.0 [R1-ip-pool-dsrw.co...

图3-4 RIP抑制接口配置网络拓扑 1.R2上抑制连接R1的接口，稍后观察R1、R2的RIP路由表 [R2]rip 1 [R2-rip-1]silent-interface GigabitEthernet 0/0/0 <R1>display ip routing-table protocol ...

图10-4 内部服务器映射（nat server）网络拓扑 图10-5 SERVER的IP配置 图10-6 SERVER的HTTP服务配置 图10-7 CLIENT的IP服务配置 1.R1配置(HTTP) [R1]interface GigabitEthernet 0/0/0 [R1-Gigab...

图7-1 基本配置网络拓扑 1.交换机关闭STP协议 [SW1]stp disable [SW2]stp disable [SW3]stp disable 2.PC1连通未知IP地址 PC1>ping 192.168.1.3 Ping 192.168.1.3: 32 data bytes, Press Ctrl_C...

1.查看OSPF路由优先级，内部OSPF优先级10，外部150 <R1>display ip routing-table protocol ospf 34.0.0.0/8 OSPF 10 12 D 12.1.1.2 GigabitEthernet0/0/0 44.1.0.0/22 O_ASE 150 2 D 12.1.1...

1.R1、R2、R3修改接口的OSPF类型 [R1]interface Serial 0/0/0 [R1-Serial0/0/0]ospf network-type p2mp [R2]interface Serial 0/0/0 [R2-Serial0/0/0]ospf network-type p2mp [R3]interface Ser...